Home > 10GbE Cards >   Single Port PCI Express CX4 10Gb Ethernet Adapter
	PETG1 $1,295.00 Special Instructions: North American Pricing Only. Product Code: PETG1 866-782-4622

Description Technical Specs   The Small Tree PETG1 server card allows you to connect your Power Mac G5 with PCIe, Mac Pro or Intel Xserve systems to a 10 Gigabit Ethernet capable switches and storage devices with CX4 connectors. The PETG1 card will provide an immediate performance increase on large transfers, especially when using jumbo frames. The distance limitation on  CX4 cables is 15m.   Product Features Key Features: • Dual protocol, 10-Gigabit Ethernet or 10-Gigabit Myrinet • PCI-Express x8 for wire-speed performance • Firmware-controlled offload engine • Low-profile add-in card Specifications: CX4 network port: 10GBase-CX4, 10+10 Gbit/s data rate, full-duplex. The port is fully compliant with the IEEE 802.3ak specifications for the 10GBase-CX4 10-Gigabit Ethernet Physical layer (PHY), and can operate with either Ethernet or Myrinet protocols at the Data Link layer. When operating in Ethernet mode, the port supports Ethernet flow control as defined by IEEE 802.3x. The port may be connected with standard 10GBase-CX4 cables up to 15m in length. PCI-Express host port: This NIC is a x8 (8 lane) PCI-Express Add-in Card. It is capable of exchanging data with a host computer at up to 2 GBytes/s (250 MBytes/s per lane) data rate in each direction, full-duplex. The port is fully compliant with the PCI-Express Card Electromechanical Specification Rev. 1.1, and with the PCI-Express Base Specification Rev. 1.0a. The circuit-board edge connector of the NIC will fit mechanically in x8 or x16 physical slots in host computers. The NIC auto-negotiates operation in the widest available mode supported by the slot it is plugged into (x8, x4, x2, or x1). Optional PCI-Express capabilities supported: Advanced Error Reporting, Device Serial Number. The hardware includes support for the following features and optional/proposed PCI-Express capabilities, which will be supported in future firmware releases: PCI-Express Base Specification Rev. 1.1, Virtual Channel Capability, Power Budgeting Capability, PCI-Express Capability Structure Expansion, and Completion Timeout Control Capability. These NICs have been tested and qualified in many commercially available motherboards and with all of the common PCI-Express chip sets. NIC processor: The NIC is based on a Myricom custom-VLSI chip called the Lanai Z8E. The RISC and other processors inside the Lanai-Z8E chip operate at 300MHz minimum. Local memory: 2MB (256Kx8B). The local memory operates from the same 300MHz clock as the processors in the Lanai Z8E, and provides 2,400 MB/s of local-memory bandwidth. Byte parity is generated and checked. The local memory is used principally for firmware execution and for buffering packet headers. Packet data is buffered inside the Lanai Z8E. EEPROM: 512KB, which includes PCI-Express Configuration Space information and the firmware required for PCI-Express port initialization and host booting. The driver loads the matching firmware as required by the mode in which the NIC is operating. The EEPROM can be re-programmed in-place by the Lanai Z8E. Future firmware releases will include an Etherboot driver. LEDs (4): The yellow LED labeled S on the PCI faceplate is controlled by the Lanai firmware; its interpretation is different for different firmware. The 3 green LEDs on the PCI faceplate indicate Link connectivity, RX traffic, and TX traffic, and are labeled L, R, and T, respectively. Physical dimensions: The circuit board is a low-profile add-in card as defined in the PCI-Express Card Electromechanical Specification Rev. 1.1: height 68.9mm (exclusive of the PCI faceplate), length 147.3mm (exclusive of the PCI faceplate), total thickness 22mm, weight 88g (including the standard PCI faceplate). The NIC can be supplied with either a standard PCI faceplate (10G-PCIE-8A-C) or a low-profile PCI faceplate (10G-PCIE-8AL-C). Power: The NIC is powered from 3.3V from the PCI-Express port, 2.5A (8.3W) maximum. Environmental: Operating: Temperature 0C to 55C up to 10,000 foot altitude. Relative humidity 15% to 80% @ 50C, non-condensing. Storage: Temperature -40C to 70C. Relative humidity 90% @ 65C. Test connector: The test connector is used for production testing, and should not be used in normal service. Regulatory Approvals: Fully compliant with EN55024 (1998 w/A1: 2001 & A2: 2003), EN55022 (1998) Class A, AS/NZS 3548 (1005 W/A1 & A2: 97) Class A, CISPR 22 (1997) Class A, FCC Part 15 Subpart B Section 15.109 Class A, VCCI (April 2000) Class A, & ICES-003 Class A (ANSI C63.4 1992). See the CE Declaration of Conformity (pdf, 29KB) and the EMC Test Report (pdf, 486 KB). Reduction of Hazardous Substances: These NICs are RoHS-compliant under the server exemption.

Related Products Intel® 10 Gigabit XF SR Dual Port Server Adapter PETG2F-XF-SR $2,995.00 Add Intel Based 10 Gb PCIE 1 Port XFP Optical 10 Gb Et PETG1F-XF-SR $1,995.00 Add Single-Port PCI-X 10Gb Ethernet Optical Adapter PXTG1F $2,495.00 Add Intel Based 10 Gb PCIE 2 Port Copper 10 Gb Et PETG2-CX4 $995.00 Add Single-Port PCI-X 10Gb Ethernet CX4 Copper Adapter PXTG1 $1,295.00 Add

 Share your knowledge of this product with other customers... Be the first to write a review.